Baso L62AA Bedienungsanleitung PDF herunterladen

Installation Instructions

Issue Date January 19, 2015

Part No. BASO-INS-L62AA, Rev. D www.baso.com

L62AA BASO® Safety Shutoff Device

Installation

WARNING: Risk of Fire or Explosion.

Do not use the L62AA in Liquefied Petroleum

(LP) gas applications. The L62AA is for use with

natural gas only. Pilot gas is not 100% shut off

and will continue to flow with the loss of pilot

flame. Use of LP gas may cause gas accumulation

and may result in severe personal injury or death.

IMPORTANT: Only qualified personnel

should install or service BASO® Gas Products.

These instructions are a guide for such personnel.

Carefully follow all instructions in this document

and all instructions for the appliance.

WARNING: Risk of Explosion or Fire.

Shut off the gas supply at the main manual shutoff

valve before installing or servicing the L62AA.

Failure to shut off the gas supply can result in the

release of gas during installation or servicing,

which can lead to an explosion or fire, and may

result in severe personal injury or death.

CAUTION: Risk of Electric Shock.

Disconnect power supply before making electrical

connections to avoid electric shock.

IMPORTANT: Make all gas installations in

accordance with applicable local, national, and

regional regulations.

IMPORTANT: Do not loosen or tighten the

brass hex nut that fastens the brass terminal

bushing to the switch housing. The machined flats

on the terminal bushing must be parallel to the

flats on the switch housing. If not, the switch power

unit may distort and cause the safety switch to fail.

To install the L62AA.

1. Turn off power to the appliance.

2. Turn off gas at the main manual shutoff valve

adjacent to the appliance.

3. Remove the L62AA cover by loosening the

screws at the side of the device (not the brass

hex nut).

4. Mount the L62AA in any convenient position

using the mounting holes provided. See Figure 1

for mounting hole locations.

5. Push the circuit wires through the conduit

opening on the bottom of the L62AA, strip the

ends of the wires just enough to put the bare

wire under the terminal screws, and attach them

to the two wire terminals (see Figure 1).

6. Replace the cover (do not loosen the brass hex

nut).

7. Attach the thermocouple securely to the pilot

burner, and screw the terminal end to the BASO

power unit terminal on the L62AA (see Figure 1

and Figure 2). Make sure that this connection is

clean. Tighten the thermocouple lead nut finger

tight plus a maximum of 1/8 turn. Do not

overtighten.

WARNING: Risk of Explosion or Fire.

Do not attach both wires to one terminal on the

L62AA. Doing so bypasses and eliminates all

safety features provided by the L62AA, can lead to

an explosion or fire, and may result in severe

personal injury or death.

WARNING: Risk of Explosion or Fire.

Verify that this device is wired in series electrically

with thermostats and other appliance operating

controls. Wiring the device in parallel with such

controls will defeat the safety features of this

device and may result in severe personal injury or

death.

1 2 3 4 5 6 7 8 9 10

Inhaltsverzeichnis

Seite 1 - Installation

Seite 2 - DO NOT REMOVE SHIELD

L62AA BASO Safety Shutoff Device Installation Instructions 5Technical SpecificationsProductL62AA BASO Safety Shutoff Device100% ShutoffNoConduit Openi

Seite 3

2 L62AA BASO Safety Shutoff Device Installation InstructionsSAFETY MECHANISMWARNINGEXPLOSION HAZARDSERIOUS INJURY ORDEATH CAN RESULTDO NOT REMOVE SHIE

Seite 4 - Repairs and Replacement

L62AA BASO Safety Shutoff Device Installation Instructions 3Setup and AdjustmentsCheckout!WARNING: Risk of Explosion or Fire.Follow this or an equival

Seite 5

4 L62AA BASO Safety Shutoff Device Installation InstructionsRepairs and ReplacementCheck the millivoltage output of the thermocouple andmilliampere dr

Seite 6

L62AA BASO Safety Shutoff Device Installation Instructions 5Technical SpecificationsProductL62AA BASO Safety Shutoff Device100% ShutoffNoConduit Openi

Seite 7

Seite 8

2 L62AA BASO Safety Shutoff Device Installation InstructionsSAFETY MECHANISMWARNINGEXPLOSION HAZARDSERIOUS INJURY ORDEATH CAN RESULTDO NOT REMOVE SHIE

Seite 9

L62AA BASO Safety Shutoff Device Installation Instructions 3Setup and AdjustmentsCheckout!WARNING: Risk of Explosion or Fire.Follow this or an equival

Seite 10 - Technical Specifications

4 L62AA BASO Safety Shutoff Device Installation InstructionsRepairs and ReplacementCheck the millivoltage output of the thermocouple andmilliampere dr

Kommentare zu diesen Handbüchern

Keine Kommentare

Baso L62AA Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Baso L62AA herunter. BASO L62AA User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Baso L62AA